 | |  | | The products in this section are real helpers. They help you make your In-Vehicle Mounting Solution even more customized and flexible at the same time. Some of the products also provide the help you need to use your device in a custom way outside your vehicle e.g. a Rental Car, RV, Boat, Home, Office etc. |
|
|
|
|  | | | | Item No. 213065 | | Position your device higher or lower on the mount. If you want to position your device higher or lower from the mount, this is what you are looking for. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface. | | |
|
 |
 | | | | Item No. 213099 | | Move your device/holder from vehicle to vehicle or place to place using only one holder. The Move Clip system is basically a Female Plate with a wide V-slot and a Male Plate that is shaped to fit into the V-slot in the Female Plate. The Male Plate slides into the Female Plate. The Female Plate attaches to a mounting bracket or any kind of flat surface. The Male Plate attaches on the back of your device or on your device holder/cradle. The Move Clip System can be used in vehicles, boats, RVs etc. It can also be attached to walls, computer monotors etc. This Move Clip is ment for moving one device between two places e.g. between two vehicles or between a vehicle and a boat etc. Dimensions: 50 x 42 x 5 mm / 1.97 x 1.65 x .19 inches. | | |
|
|
 | | | | Item No. 213098 | | Switch between two or more devices/holders using only one dashboard mount. The Move Clip system is basically a Female Plate with a wide V-slot and a Male Plate that is shaped to fit into the V-slot in the Female Plate. The Male Plate slides into the Female Plate. The Female Plate attaches to a mounting bracket or any kind of flat surface. The Male Plate attaches on the back of your device or on your device holder/cradle. The Move Clip System can be used in vehicles, boats, RVs etc. It can also be attached to walls, computer monotors etc. You can have as many of each part as you want to. This Move Clip Kit is ment for switching between two devices using one dashboard mount etc. Dimensions: 50 x 42 x 5 mm / 1.97 x 1.65 x .19 inches | | |
|
 | | | | Item No. 213093 | | Our Move Clip System allows you to easily move your device in and out of the vehicle. | | |
|
 | | | | Item No. 213091 | | Add more Female Plates to expand one of the above listed Move Clip Kits or build your own kit. | | |
|
 | | | | Item No. 213092 | | Add more Male Plates to expand one of the above listed Move Clip Kits or build your own kit. | | |
|
 | | | | Item No. 215159 | This option is a good option in those cases we do not provide a Holder for your device. Please check for holders under Device Holders on the upper left side of the page.
Two plate mounting system for mounting and moving small Tablet PCs, UMPC, Monitors, GPS and Satellite Radio devices etc. | | |
|
 | | | | Item No. 215058 | | For use with devices/device cradles that use the Richter mounting system - usually attached to a windshield suction cup mount. The Richter system has 4 pins extending out from the plate. | | |
|
 | | | | Item No. 215198 | | This adapter plate has 2 T prongs extending out from the base plate. Unhook your device from your windshield suction cup mount and slide it onto the 2 T prong adapter used in combination with our Vehicle Mount. The 2 T prong system is used with most Magellan?s, the HP branded iPAQ rx5000 Car Cradle, and many other devices as well. NOTE: Some of the early releases of various Magellan devices only use 1 T prong. If so, please select the 1 T Prong Vehicle Adapter listed below. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | Item No. 215199 | | This adapter plate has 2 T prongs extending out from the base plate, and a Tilt Swivel on the back that provides easy adjustment of your device for better viewing. Unhook your device from your windshield suction cup mount and hook it onto the 2 T prong adapter used in combination with our Vehicle Mount. The 2 T prong system is used with most Magellan?s, the HP branded iPAQ rx5000 Car Cradle, and many other devices as well. NOTE: Some of the early releases of various Magellan devices only use 1 T prong. If so, please select the 1 T Prong Vehicle Adapter listed below. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | Item No. 215225 | | This adapter plate has 1 T prong extending out from the base plate. Unhook your device from your windshield suction cup mount and slide it onto the 1 T prong adapter used in combination with our Vehicle Mount. The 1 T prong system was used with early versions of some Magellan?s and many other devices. NOTE: The newer releases of various Magellan devices use 2 T prongs. If you have this, please select the 2 T Prong Vehicle Adapter listed above. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or 2 prong T extending from the mount. | | |
|
|
 | | | | Item No. 215231 | | This adapter plate has 1 T prong extending out from the base plate, and a Tilt Swivel on the back that provides easy adjustment of your device for better viewing. Unhook your device from your windshield suction cup mount and slide it onto the 1 T prong adapter used in combination with our Vehicle Mount. The 1 T prong system was used with early versions of some Magellan?s and many other devices. NOTE: The newer releases of various Magellan devices use 2 T prongs. If you have this, please select the 2 T Prong Vehicle Adapter listed above. If you are not sure what you have, just unhook your device from the suction cup mount and you can easily see if you have a 1 prong or a 2 prong T extending from the mount. | | |
|
 | | | | Item No. 213019 | | Angle your holder/device for a better viewing position. Same as item no. 213018 above but it extends from center to better avoid interference between your device and dashboard buttons, gear shift etc. | | |
|
 | | | | Item No. 215200 | | Tilt Swivel Mount, Large for installation of heavier devices such as larger monitors, laptops etc. Allows you to adjust the angle of the device and provides a flexible yet firm installation. | | |
|
 | | | | Item No. 215163 | | Increase the angle of your Holder an additional 15 degrees by placing this Wedge between the Holder and the Vehicle Mount. | | |
|
 | | | | Item No. 215162 | | Increase the angle of your Holder an additional 10 degrees by placing this Wedge between the Holder and the Vehicle Mount. | | |
|
 | | | | Item No. 215052 | | Dimensions 50 x 50 x 8 mm/ 2 x 2 x 0.3 inches If you are using a device with a belt clip on the back or a case with a button on the back, you can conveniently hang it in your car or on a wall using the Button and Clip Holder. You do not have to remove your device from its case. The V-slot is designed for the buttons and the opening going through the holder is designed for the clip to slide through. The Button and Clip Holder will accommodate devices, cases, or holsters that have buttons or belt clips. The reason we have a small and a large version of this part is to accommodate the thickness of the bottom part of the clip, which varies from clip to clip, especially for two-way radios. | | |
|
 | | | | Item No. 848636 | | Fits Full size iPods, some Smart Phones, MP3 Players, PDAs etc as long as the device is wide enough. NOTE: This Holder is adjustable and is intended to be used for devices with silicone type cases e.g. iSkin, Jam Jacket, Speck, XtremeMac, Showcase etc. | | |
|
 | | | | Item No. 710620A | | Unfortunately we don't have any custom holder for your device. However, you can try our Universal Holder - Stick-on button and V-slot plate. It holds your device securely in place on the dashboard and it doesn't swivel. The adhesive on the back of the Stick-On Button is very strong. The Stick-On Button can be attached to any flat or slightly curved surface e.g. back of cell phone, PDA, Remote Control, Cordless Phone, MP3 Player etc. The V-slot plate can be screwed onto our vehicle dashboard mount or any flat surface. | | |
|
 | | | | Item No. 202008 | | Perfect for use in rental cars! The ProClipTravel Mount attaches to the windshield with a suction cup. | | |
|
 | | | | Item No. 215143 | | Keep your device within easy reach at home or in the office. Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | Item No. 215396 | | Keep your device within easy reach at home or in the office! Attach a Device Holder for a mobile phone, PDA, MP3-player or any device you want to have within easy reach. Also good for remote controls and chargers. | | |
|
 | | | | Item No. 215100 | | Keep a notepad and pen handy. Notepad and pen included. Attaches to any of our ProClip Vehicle Mounts. Not for use while driving. | | |
|
 | | | | Item No. 215265 | | 5-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | Item No. 215264 | | 10-pack of notepad refills to be used with our Notepad Holder with Tilt Swivel. | | |
|
 | | | | Item No. 215083 | | The ProClip Handlebar Mount attaches securely to round handlebars. The Tilt Swivel accommodates all ProClip Device Holders and other device holders with the AMPS Hole Pattern. 1 inch diameter when closed. | | |
|
 | | | | Item No. 215181 | | Do not attach to a ProClip Vehicle Mount. This part is to be used instead of the ProClip Vehicle Mount. Do you need your device closer to you? This goose neck mount will extend your device closer. It can be screwed into any flat surface and the goose neck can be adjusted to face you for optimal viewing. Attach a Holder to the face plate of the mount and you are all set. | | |
|
 | | | | Item No. 215228 | | If you want to extend your device upwards from the Vehicle Console Mount for better viewing, this is what you are looking for. This item can be used with or without a Tilt Swivel, which is not included, but can be found by clicking Tilt & Swivel Mounts on the left side of the page. Then select Tilt Swivel Mount. (Item # 215453) | | |
|
 | | | | Item No. 710643 | | The ProClip Suction Cup Adapter Plate will allow you to attach your suction cup directly to your Vehicle Mount. | | |
|
Shopping Cart Summary
You Just Added ():
-
Total Qty: @
Total: USD $ Items in Your Cart:
Cart Subotal: USD $ Close |
| |
|
|
|
|
|
